The SOLIDWORKS Split feature divides one solid part into multiple separate solid bodies, using a plane, face, or surface as a trimming tool. You can keep the resulting bodies in the same part file or save them as separate part files; use Split Line instead when you only want to divide a face, not a solid body.
What the Split feature does
Split is a multibody-part feature. It takes existing solid geometry and uses one or more trim tools to divide it into regions. The regions that result are listed as bodies in the part’s Solid Bodies folder in the FeatureManager design tree. They remain in one part document unless you save them out as separate files.
For example, imagine a rectangular block that needs to become two components along a diagonal interface. A plane positioned diagonally through the block can divide it into two solid bodies. You can retain both bodies, discard one, or save each retained body as its own part. The feature does not automatically turn the bodies into separate files or create a physical gap between them.
A split can be useful for modeling components that share a starting shape, preparing bodies for separate manufacturing operations, or dividing a design into pieces for later assembly. It is not the same as physically cutting material away: the goal is to create distinct bodies from the existing solid, rather than simply remove a volume as a typical cut feature does.
Split versus Split Line
The similar names cause confusion, but the features have different jobs. Split divides solid geometry into separate solid bodies. Split Line creates edges on faces by projecting a sketch, using a silhouette, or finding an intersection, depending on the selected Split Line method. It can divide a face into regions, but by itself it does not create separate solid bodies.
Use Split when you need separately selectable or exportable volumes. Use Split Line when you need a boundary on a surface—for example, to define a region for an appearance, a parting line, or a later face-selection operation. If the goal is simply to show a line on a model, a sketch may be enough; if the line must become an edge on the model’s face, Split Line is the more relevant tool.
How the feature works
The trim tool determines where SOLIDWORKS divides the model. A plane is a straightforward choice for a flat division. A planar face or reference plane can serve a similar purpose, while a surface can provide a more involved boundary. The tool must intersect the solid in a way that actually separates it; a tool that merely touches the outside or stops short may not create the intended multiple bodies.
After you define the trim tool, the Cut Part command calculates the regions produced by the division. The Resulting Bodies list lets you choose which regions to keep. If you retain multiple regions, they become separate bodies within the same part document. Their faces may meet at the split boundary, but the bodies are still distinct objects in the model.
The result depends on the geometry and the position of the tool. A single plane passing through a simple block commonly creates two bodies. A more complex shape or multiple trim tools can produce a different number of regions. It is better to check the preview and resulting-body list than to assume that every split creates exactly two bodies.
Steps to split a part
Start with a part that contains the solid you intend to divide. Create or identify a suitable plane, face, or surface first, and make sure it crosses the solid where the boundary should be. Then use the Split command from the part environment.
- Choose Insert > Features > Split.
- In the Split PropertyManager, select the trim tool or tools that define the division.
- Click Cut Part to calculate the resulting regions and inspect the preview.
- In the Resulting Bodies list, select the bodies you want to retain. Check that the preview shows the intended geometry.
- Confirm the feature. The kept bodies appear in the part’s Solid Bodies folder.
- If separate part documents are needed, use the save-bodies option in the workflow or the Save Bodies feature to create them.
Names and available controls can vary slightly with SOLIDWORKS version and the exact workflow. If the command is not visible on the CommandManager, the Insert menu provides a reliable route in the part environment. Save the part before making substantial downstream edits, especially if separate files will reference the original multibody part.
Choosing a trim tool
Choose the simplest tool that creates the boundary you need. A reference plane is convenient when the division is flat and may need to move later: editing the plane’s position can update the split. A planar face works well when the boundary should follow existing model geometry. A surface is useful when the intended separation is not represented by a simple plane, but it can require more careful positioning and inspection.
- Plane: useful for a straight, adjustable division through a part.
- Planar face: useful when an existing face provides the desired orientation or location.
- Surface: useful for a boundary shaped by surface geometry rather than a flat plane.
For instance, to separate a molded housing into upper and lower regions along a flat joint, a plane or existing planar face is usually easier to manage than a complex surface. To divide a curved part along a shaped boundary, a surface may be more appropriate. Regardless of tool type, check whether it intersects the entire intended region and produces clean bodies without tiny slivers or unintended fragments.
Keeping bodies in one file or saving them separately
Keeping the bodies together in a multibody part is often useful during early design. One document preserves their common origin and makes it easy to inspect the division, adjust the trim tool, and manage the overall shape. This can be a good choice when the bodies are still being developed as parts of one design or when a downstream process expects a multibody model.
Saving the bodies as separate part documents is useful when components need independent drawings, part numbers, or assembly placement. SOLIDWORKS can create part files from the resulting bodies; the save-bodies workflow can also be used to create an assembly from them. Where the saved files retain references to the source part, changes to the source can affect the derived parts, so keep the source file available and avoid casually breaking links if associativity matters.
Choose a clear naming scheme when saving several bodies. Names such as “Housing_Top” and “Housing_Base” are easier to identify than generic body numbers. Also review the saved files after the operation: confirm the correct body went into each file, and verify the destination folder and file names before sharing or moving the documents.
Common problems and fixes
If the split does not create multiple bodies, first check whether the trim tool actually crosses the solid. A plane that ends at a tangent contact, or a surface that does not form a separating boundary, may fail to divide the volume as expected. Move or extend the tool, select the correct face or surface, and use the preview before accepting the feature.
If too many bodies appear, inspect the geometry for small intersections or extra regions created by the tool. A complicated surface can divide a model in more places than intended. Simplifying the tool, changing its position, or splitting the part in more than one deliberate operation can make the result easier to understand.
Other useful checks include:
- Confirm that the selected entity is a suitable trim tool, not merely a sketch or edge that does not define a separating region.
- Review the Resulting Bodies list and ensure the desired regions are selected to keep.
- Look for narrow sliver bodies caused by a tool passing very close to a vertex or edge.
- If later features fail, inspect their references: a feature that depended on a face may need repair if the split changed the face layout.
Face and edge references can change when upstream geometry changes. This is a general parametric-modeling concern, not unique to Split. A stable reference plane or carefully defined surface can make the design easier to edit than relying on an incidental edge whose location may change.
When another feature is a better choice
Use Cut with Surface when the intent is to remove material on one side of a surface rather than preserve both sides as separate bodies. Use an appropriate cut feature, such as Cut-Extrude, when you want to remove a defined volume from a part. Those operations serve a different design purpose from dividing and retaining multiple regions with Split.
Use Split Line for face boundaries, as described above. If the model needs to become a collection of components with independent positions and assembly relationships, saving bodies may be a useful bridge from a multibody part, but a purpose-built assembly can be more suitable when the components need independent motion or assembly-level mates. The right choice depends on whether you are dividing geometry, removing material, marking a face, or organizing components.
Frequently Asked Questions
Does the SOLIDWORKS Split feature create separate part files?
Not automatically in every workflow. Split creates separate bodies in the part document. Use the save-bodies workflow to create separate part files, and create an assembly from those files if that is part of the design process.
Can Split divide a part into more than two bodies?
Yes. The number of resulting bodies depends on the shape and how the trim tool or tools intersect it. Review the preview and Resulting Bodies list rather than assuming one tool will always produce two bodies.
Does Split remove material?
Split is intended to separate a part into resulting bodies, not to use one side of a cut as waste material. You choose which resulting bodies to keep. For a material-removal operation, use a suitable cut feature instead.
Why does Split Line not make two solid bodies?
Split Line creates edges or boundaries on faces; it does not perform the same body-separation operation as Split. Choose the Split feature when the required result is multiple solid bodies.
Can I edit a split after creating it?
Usually, you can edit the Split feature in the FeatureManager tree to change its trim tools or resulting-body choices. If later features depend on geometry that changes, those features may need repair or new references.
Related
- C++ String Erase: How std::string::erase Works
- How to Split an Object in Onshape: A Step-by-Step Guide
- What Is a Split Queen Sheet? Size and Fit Explained
Try it: the Date Difference Calculator: days, months, years and weekdays between two dates, with the DATEDIF formulas.
More in How-to basics
- Mail Merge in Word in Hindi: Complete Step-by-Step GuideTo create personalized Hindi letters in Word, prepare an Excel list with one person per row, write your…
- How to Delete a Page in Word UK: A Practical GuideTo delete a page in Word, remove the text, paragraph marks or break creating it; Word does not…
- How to De-Identify Track Changes in Microsoft WordTo de-identify tracked changes in Word while keeping the edits visible, save a copy, enable Word’s personal-information removal…
- Excel Data Validation Drop-Down Lists: Setup and FixesTo create a drop-down list in Excel for Microsoft 365 on Windows, select the cells, choose Data >…
- Excel Table Maker: Create and Format Tables EasilyExcel has a built-in table maker: select your data, press Ctrl+T on Windows, confirm whether it has headers,…
- Lock Cells in Excel for Scrolling with Freeze PanesTo keep headings or identifying columns visible while you scroll in Excel, use View > Freeze Panes. Select…
Sources: Function behaviour and menu paths: Microsoft Support documentation for Excel. Method & sources
Spotted an error in this guide? Let us know.