SOLIDWORKS Split Command: How to Divide a Part File

How-to basics · Updated November 22, 2026

The SOLIDWORKS Split command divides a part into separate solid or surface bodies using a plane, face, or surface as a trimming tool. Find it in a part document under Insert > Features > Split; the resulting bodies can remain in one part file or be saved as separate part files.

What the Split command does

Split is a part feature for dividing model geometry, not a command that merely draws a line on a face. You select geometry that intersects the part, use it to define where the model is cut, and then choose which resulting bodies to keep. The split bodies appear in the part’s Solid Bodies or Surface Bodies folder in the FeatureManager design tree, depending on the geometry.

A simple example is a rectangular solid divided by a plane through its middle. After the feature is created, the part contains two separate solid bodies. Both bodies are still managed by the same part document unless you save them out as separate files. The feature remains in the model’s history, so you can edit its trimming tool or settings later, subject to downstream features and references.

This is useful for designing a part that will be manufactured or handled as multiple pieces, separating regions for later operations, or preparing components for an assembly. It does not automatically create a physical gap, add fasteners, or make the pieces into an assembly. Those are separate design decisions.

How to use Split in a part

Start with a part that has solid or surface geometry and a suitable trimming tool. A plane is often the easiest tool to control; an existing planar face or surface can also define a cut when it crosses the model. The exact selections depend on the shape and the result you need.

  1. Open the part and create or identify a plane, face, or surface that passes through the area to divide.
  2. Choose Insert > Features > Split. You can also search for Split using SOLIDWORKS command search if you do not see it in the menus.
  3. In the Split PropertyManager, select the trimming tool or tools. Check the preview to confirm that the tool intersects the geometry and produces the intended divisions.
  4. Click Cut Part to calculate the resulting bodies. Select the bodies you want to retain in the resulting-bodies list.
  5. Confirm the feature. If you need separate files, use the Save Bodies workflow to name and save the bodies.

Pay attention to the preview before accepting the feature. A trimming surface that stops short of the model, touches it only tangentially, or crosses it in an unexpected location may produce no cut or a different number of bodies than expected. If the preview is unclear, adjust the plane or surface, then recalculate the split.

Choosing a trimming tool and cut location

The trimming tool determines where the body is divided. A reference plane is usually a good choice for a straight, predictable division because you can reposition or redefine it in the tree. A planar face may be convenient when the desired cut should align with existing geometry. A surface can define a more complex boundary than a flat plane, provided it intersects the part in a way that divides it into valid regions.

Before creating the feature, consider what the cut is meant to accomplish. For instance, if a molded housing needs a top cover and a lower shell, a plane or surface placed along the intended parting region may help separate the geometry. If the aim is instead to remove material and leave one continuous body, a cut feature may be more appropriate. Split is about creating body boundaries; it does not decide which side is the finished component.

  • Use a plane when a simple, adjustable planar division is enough.
  • Use a face when an existing face already marks the desired division.
  • Use a surface when the split needs to follow a non-planar boundary and the surface properly intersects the model.

When more than one trimming tool is involved, inspect the result carefully. Multiple intersections can create several regions, and the result may include more bodies than the two you initially expected. The body list is the final check: identify each previewed region and retain only the bodies the design requires.

Keeping bodies together or saving separate files

A common point of confusion is whether Split automatically makes separate part documents. It does not have to. The feature can leave the resulting bodies inside the original multibody part, which is useful when they share design history or when you are still developing the overall shape. They can also be saved as individual part files when a downstream workflow needs separate components.

To create separate files, use Save Bodies, available from the part’s feature commands or by right-clicking the Solid Bodies folder in the FeatureManager design tree. Select the bodies to save, provide file names and locations, and use the available assembly option if you want SOLIDWORKS to create an assembly from the saved bodies. Review the prompts and file locations in your installed version, especially if you are working with an existing assembly or files that already have names.

Saving bodies introduces file references: the original part and any assembly may depend on the saved part files being available. Keep related files together or use a managed project location, and avoid renaming or moving referenced files casually. If you only need separate bodies for later features in the same design, keeping them in the multibody part can be simpler than creating additional documents.

Split compared with similar SOLIDWORKS tools

Several SOLIDWORKS tools use similar words, but they solve different problems. Choose based on whether you need to divide a body, split a sketch entity, mark a face, or remove material.

  • Split feature: divides part geometry into separate bodies using a trimming tool. It is the relevant choice when the goal is multiple bodies or saved body files.
  • Split Line: creates edges on faces by projecting or intersecting sketch or other geometry. It is commonly used to divide a face visually or to support later operations; it should not be confused with separating a solid into bodies.
  • Trim Surface: trims surface geometry. It is useful in surface modeling, but it is not the same workflow as splitting a solid part into retained bodies.
  • Cut-Extrude or another cut feature: removes material from a body. A cut may create separate regions if it passes completely through the part, but its primary purpose is a material-removal operation rather than managing selected resulting bodies with Split.
  • Split Entities in a sketch: divides a sketch segment into smaller entities. It changes the sketch, not the solid body into separate part bodies.

For example, if a line needs to appear across a curved face for a later selection or appearance, Split Line may be the right feature. If a block must become two independently selectable solid bodies, use Split or an appropriate solid cut that yields separate bodies. If you only need a seam in a sketch, use the sketch editing tools instead.

Common problems and ways to fix them

If Split produces no bodies or the preview does not show a division, first confirm that the trimming tool actually intersects the model. A plane placed beside the part cannot divide it. If the tool is a surface, check its size and position; extending or adjusting the surface may be necessary so it crosses the intended region.

If the feature creates an unexpected number of bodies, examine every intersection between the tool and the model. A curved surface or multiple tools can divide a part into more regions than a single straight cut. Use the resulting-bodies list and the graphics preview together rather than assuming that every cut produces exactly two pieces.

If a body disappears after the operation, it may not have been selected for retention. Reopen the Split feature and check the resulting-bodies selection. Also consider whether a later feature in the tree consumes, removes, or changes the body. The FeatureManager history helps identify whether the issue begins at Split or in a downstream operation.

Other useful checks include:

  • Rebuild the model after changing the trimming tool and watch for feature errors.
  • Make sure the selected plane, face, or surface belongs to the intended model context.
  • Use clear names for reference planes, split features, and saved bodies so later edits are easier to understand.
  • If saved files or an assembly cannot find a body file, verify the file path and references rather than recreating the split immediately.

Planning a robust split feature

Like other history-based features, Split depends on geometry and references earlier in the FeatureManager tree. A plane tied to stable reference geometry is generally easier to maintain than a selection that relies on a face likely to change after edits. If the part is expected to evolve, consider how changes to its dimensions could move the cut or alter the number of resulting bodies.

Give the feature a descriptive name, such as “Separate cover from base,” rather than leaving a long model with several features called Split. When saving bodies, use meaningful names that correspond to the design or assembly role. Clear naming does not change geometry, but it reduces mistakes when selecting bodies, reviewing a model, or sharing files with another person.

Also decide early whether the design is best represented as one multibody part or as separate part documents. A multibody part can keep related geometry together and support coordinated edits. Separate files are more suitable when the bodies need independent part documents or an assembly-level workflow. Neither arrangement is automatically correct for every project; choose according to how the components will be edited, documented, and used downstream.

Frequently Asked Questions

Where is the Split command in SOLIDWORKS?
In a part document, go to Insert > Features > Split. If you cannot find it, use SOLIDWORKS command search and search for Split. The command is intended for part geometry, not for splitting a sketch line.

Does Split create two separate part files?
Not by itself. Split creates resulting bodies in the part. Use Save Bodies to write selected bodies as separate part files, and use its assembly option if you also need an assembly made from them.

What is the difference between Split and Split Line?
Split divides model geometry into separate bodies. Split Line creates edges or divides face regions using selected geometry; it does not, by itself, turn one solid into separate solid bodies.

Can I use a plane to split a SOLIDWORKS part?
Yes. A plane is a common trimming tool. Position it so it intersects the part where you want the division, then inspect the Split preview and resulting-bodies list before accepting the feature.

Why is Split not cutting my part?
The trimming tool may not intersect the model, or its position may not divide the geometry into separate regions. Check the preview, reposition or extend the tool as appropriate, and confirm that the intended bodies are selected for retention.

Related

Try it: the Date Difference Calculator: days, months, years and weekdays between two dates, with the DATEDIF formulas.

More in How-to basics

Sources: Function behaviour and menu paths: Microsoft Support documentation for Excel. Method & sources

Spotted an error in this guide? Let us know.