Onshape Split Function: How to Split Parts and Faces

Formulas & functions · Updated November 22, 2026

In Onshape, the Split feature divides a part into separate pieces or divides a face into smaller faces. In a Part Studio, choose Split from the feature toolbar, select whether to split a part or a face, then select the geometry and splitting entity required for that operation.

What the Split feature does

Split is a modeling feature used to divide existing geometry. When you split a solid part, the result can be multiple parts in the Part Studio; when you split a face, the result is a face boundary change on the same part, not a new solid. This distinction matters: splitting a face can make regions easier to select or apply different appearances to, but it does not by itself cut the body into separate pieces.

The dividing geometry is often called the splitting entity or tool. Depending on the operation, it can be a plane, face, surface, or suitable sketch geometry. It must intersect or define a boundary on the target geometry in a way that produces a valid division. A line or plane that misses the part cannot split it.

Split is a feature in the Part Studio feature sequence, so it is normally editable later. It is not the same as cutting a physical part, separating an assembly, or using a sketch command to trim curves.

Where Split fits in an Onshape workflow

Onshape models are built from features in a Part Studio. A typical workflow might create a solid with an Extrude, add details, and then use Split to divide that solid. The resulting parts appear in the Part Studio and can be used in later features or inserted into an Assembly as separate components.

A common reason to split a model is to prepare separate components for manufacturing or assembly. For example, a designer may model a single enclosure and divide it along a plane to create a lid and a base. Another use is to separate a region of a part for a later operation, or to create separate pieces that can be assigned different materials or appearances.

Splitting a part does not automatically create an Assembly, add fasteners, or define how the pieces fit together. It changes the Part Studio geometry. Assembly placement and relationships are handled separately.

Split part versus Split face

Choose the operation based on what you want to change:

  • Split part: Divides a solid part using a selected splitting entity. A successful cut can produce two or more independent parts, depending on the geometry and the splitting tool.
  • Split face: Divides one or more selected faces into smaller faces. The solid remains one part; only its face boundaries change.

For instance, if a flat panel needs to become two separate solids, use Split part with a plane that crosses the panel. If the panel must remain one solid but you need two selectable regions on its surface, use Split face with appropriate dividing geometry. Choosing Split face when you intend to create separate pieces is a frequent source of confusion.

How to split a part with a plane

A plane is a convenient splitting tool because its position and orientation are easy to control. Before starting, confirm that the plane actually crosses the part where you want the division. Create or select a suitable plane in the Part Studio, then:

  1. Open Split from the Part Studio feature toolbar.
  2. Choose the part-splitting operation in the Split dialog.
  3. Select the part or parts to divide.
  4. Select the plane as the splitting entity.
  5. Review the preview and any options in the dialog, then confirm the feature.

After confirming, inspect the Part Studio parts list and the model. If the intended halves have not both been retained, check the available split options and feature selections. The exact result depends on the geometry and settings, so do not assume that a plane will always produce exactly two useful pieces. A plane can intersect a complex or disconnected shape in several places.

For a lid-and-base example, place the plane at the desired separation height and verify that it crosses the full enclosure. If the plane only grazes a corner, the result may be an unintended sliver or no usable split. A section view or an angled view can help confirm the plane’s location before accepting the feature.

Choosing a splitting entity

The best splitting entity is the simplest one that defines the boundary you need. A plane works well for straight, planar divisions. An existing planar face can be useful when another part already defines the separation. A surface can create a curved separation where a flat plane would not follow the required shape. Sketch geometry may be appropriate for a face split or another supported split workflow, but it must intersect the target in a valid way.

  • Use a plane for a flat cut such as dividing a block at a chosen height.
  • Use an existing face when the desired split should align with that face.
  • Use a surface when the dividing boundary needs to be curved or shaped.
  • Use sketch geometry when the operation supports it and the sketch provides a clear, intersecting boundary.

When selecting geometry, pay attention to the selection field currently active in the dialog. A click may be accepted as the part to split when you intended to select the tool, or vice versa. If the preview looks wrong, clear the selection and populate each field deliberately.

Using Split face

Split face is useful when a face needs additional boundaries without separating the underlying solid. Start Split, choose the face-splitting operation, select the target face or faces, and provide the supported splitting geometry. Check the preview to confirm that the new boundary divides the face in the intended place.

For example, a designer may want two distinct regions on a broad surface so each region can be selected independently for a later modeling step or appearance assignment. Splitting the face creates that selection boundary while preserving the continuous solid. It does not create a seam with physical thickness, remove material, or make two assembly components.

If your goal is a visible groove or gap, a face split alone is not enough. Use a material-removal feature, such as an appropriate Extrude operation, or model the gap explicitly. A boundary between faces is a geometric division, not necessarily a visible or physical cut.

How Split behaves in the feature tree

Because Split is a feature, its result depends on the model state and selections that precede it. If you change an earlier sketch, plane, or feature, the split may update, move, or fail. This is useful for design changes, but it means that a split should be based on stable references when possible.

Give important planes and sketches clear names, and avoid selecting geometry that is likely to disappear after an upstream edit. If a feature later in the tree needs one of the split pieces, check its references after changing the split. A feature may need to be reselected if the division changes which part or face it refers to.

When the result is not as expected, edit the Split feature rather than rebuilding the whole model immediately. Confirm the operation type, target selection, splitting entity, and any options in the dialog. The feature preview is a useful way to check the intended outcome before accepting changes.

Common problems and how to fix them

  • The split fails or produces no change: The splitting entity may not intersect the target, or the selected geometry may not be supported for that operation. Move or extend the tool, choose another entity, and inspect the preview.
  • Only one resulting piece is available: Review the split dialog’s options and selections. Also check whether the tool divides the part as intended; a plane that only clips an edge may not create the two substantial regions you expected.
  • The wrong object is split: Check the selection field and remove unintended selections. Select the target part separately from the splitting entity.
  • The feature breaks after an edit: An upstream change may have removed or altered a referenced face, edge, or plane. Edit the feature and select a stable replacement reference.
  • The split line is visible, but the part is still one body: You may have used Split face. Change to Split part if the goal is to create independent solid pieces.

For difficult geometry, simplify the split. A clean plane or a simpler surface can be more reliable than a complicated tool with tiny edges or near-tangent intersections. If a split produces very small fragments, reconsider the tool position and whether those fragments are intentional.

Split compared with other Onshape tools

Split is appropriate when you want to divide geometry and retain the resulting regions or parts. It is different from Boolean operations, which combine or subtract overlapping solids. For example, use Boolean subtract when one solid should remove material from another; use Split when a tool should define a division rather than act as a cutting solid that is subtracted.

It is also different from an extruded cut. An Extrude configured to remove material creates a removed volume and may leave one body or separate bodies depending on the geometry and settings. Split instead uses a selected boundary or tool to divide the target. Choose based on the desired model result, not just on which command seems quickest.

For an assembly made from separate manufactured items, splitting a single Part Studio part may be a useful preparation step, but it does not replace Assembly tools. Once the parts exist, insert them into an Assembly and position or constrain them as needed.

Frequently Asked Questions

Where is the Split function in Onshape?
Open a Part Studio and choose Split from its feature toolbar. The dialog lets you choose the type of split and select the target geometry and splitting entity.

Does Split create two parts?
Split part can create separate parts, but the number and shape depend on how the splitting entity intersects the model and on the dialog settings. Split face only divides faces; it does not create additional solid parts.

Can I split a part with a sketch?
Some split workflows accept sketch geometry, depending on the operation and the geometry involved. Check the selection field and preview. A sketch that does not intersect or define a valid boundary will not produce the intended split.

Can I undo or change a Split feature?
You can edit the Split feature in the Part Studio feature list to change its selections or settings. Later features may depend on its resulting parts or faces, so review those features after making a change.

What is the difference between Split part and Split face?
Split part divides solid geometry into parts. Split face creates additional boundaries on faces while keeping the solid as one part. Choose the first to separate components and the second to divide selectable surface regions.

Related

Try it: the Formula Explainer: paste any formula and see each function and reference in plain English.

More in Formulas & functions

Sources: Function behaviour and menu paths: Microsoft Support documentation for Excel. Method & sources

Spotted an error in this guide? Let us know.