SOLIDWORKS Split Part: Create Two Separate Bodies Guide

How-to basics · Updated November 22, 2026

Yes. In SOLIDWORKS, use Insert > Features > Split with a plane, face, surface, or suitable sketch as the trim tool to divide a solid into bodies; to make two separate part files, save the resulting bodies with Save Bodies.

What the Split feature does

Split divides one solid body into two or more solid bodies inside the same part document. It does not automatically mean you have created two independent SOLIDWORKS part files. After the split, the bodies remain components of a multibody part until you save them separately or use them in another workflow.

This distinction matters because “part” can mean either a SOLIDWORKS document or a solid body within a document. A single part file can contain several solid bodies. The Split feature changes the body structure of the model, while Save Bodies is the step that creates separate files from selected bodies.

For example, imagine a rectangular block that must be divided across its middle. A plane through the block can act as the trim tool. The Split operation produces two solid bodies, one on each side of that plane. You can keep them together in the original multibody file, or save each body as its own part document.

Prepare the model and choose a cut location

Before splitting, decide where the boundary should be and make sure the trim tool actually divides the solid. A plane that touches a block but does not pass through it will not separate the block into two volumes. Likewise, a surface that stops inside the model may fail to divide it if it does not create a complete separation.

For a simple straight cut, create or choose a plane that crosses the entire solid. Use Insert > Reference Geometry > Plane to create a plane at an offset or, where appropriate, centered between selected parallel references. You can also use an existing planar face or reference plane. For a non-flat boundary, create a suitable surface that intersects the solid where the division is intended.

It is helpful to consider the downstream design before choosing the split position. If the two bodies will become separate components in an assembly, leave enough material for the intended fit and account for any gap, clearance, or joining method. The Split feature only divides geometry; it does not automatically add a manufacturing gap, fasteners, or a connection between the resulting pieces.

How to split a part into two bodies

  1. Open the part and confirm that the solid body you want to divide is present. If the file contains multiple bodies, identify the correct one in the FeatureManager design tree.
  2. Create or select a trim tool that crosses the body at the desired location. For a straight split, a plane or planar face is often the simplest choice.
  3. Choose Insert > Features > Split. In the Split PropertyManager, select the trim tool or tools. The available selection depends on the model and SOLIDWORKS release; common trim tools include planes, faces, surfaces, and sketches.
  4. Click Cut Part in the PropertyManager to calculate how the tool divides the solid. Review the resulting bodies shown by the feature.
  5. Check that the result contains the intended pieces. If the cut produces more bodies than expected, or leaves the original body unchanged, adjust the trim tool and rebuild the feature.
  6. Accept the feature. The part now contains the resulting solid bodies. Save the part document, and use Save Bodies if you need independent part files.

The exact labels and arrangement of PropertyManager controls can vary slightly between SOLIDWORKS versions, but the general sequence is to select a trim tool, calculate the cut, inspect the resulting bodies, and accept the feature. If the model has more than one solid, be attentive to which bodies the tool intersects; a single trim tool may divide several bodies at once.

Save the two bodies as separate part files

To make two editable part documents, use Save Bodies after creating the split. Depending on your workflow and version, you can access it from the multibody-part tools or from the Split feature workflow. Select the bodies to save, provide file names and a destination folder, and complete the save operation. SOLIDWORKS can maintain references between the original multibody part and the saved body files, which can help keep derived parts associated with their source.

Use clear names that describe each piece, such as Housing_Left and Housing_Right, rather than relying on generic body names. Then open each saved file to confirm it contains the intended geometry. If you are assembling the pieces, create or open an assembly and insert the two part files there. Saving bodies does not, by itself, fully position them as an assembly with mates.

Keep the original multibody part if it serves as the master design or if you expect the cut location to change. When the saved bodies are linked to their source, changing the original feature may update downstream files, but file paths and references must remain valid. Moving or renaming files outside SOLIDWORKS can make references harder to resolve, so use SOLIDWORKS file-management tools or update references deliberately when reorganizing a project.

Split compared with other SOLIDWORKS tools

Split is a good fit when one existing solid needs to become multiple bodies along a defined trim tool. Other tools may be more appropriate when the design intent is different:

  • Cut-Extrude: Use this when a sketch profile should remove material. It is often the natural choice for a slot, pocket, or cut that does not necessarily separate the entire solid into independent pieces.
  • Cut with Surface: Use a surface as the cutting boundary when the intended division is curved or otherwise cannot be described by a simple plane. The surface must intersect the solid in a way that creates the desired separation.
  • Shell or cavity-related features: These change internal or wall geometry, rather than simply dividing a solid into bodies.
  • Assembly components: If the objects are meant to be independently positioned, constrained, or managed from the start, designing separate part files and placing them in an assembly may be clearer than keeping them in one multibody part.

Do not confuse Split with Split Line. Split Line creates edges or divides faces on a model, often for appearance, selection, or downstream operations. It does not normally turn one solid into two separate solid bodies. If the goal is two physical pieces, check the body count after using the feature rather than judging only by visible edges on the model.

Common problems and how to fix them

If SOLIDWORKS will not create the split, first check whether the trim tool intersects the solid. A plane that is parallel to the desired cut but offset beyond the body will not divide it. Move the plane or edit the surface so the tool crosses the model. For a curved surface, inspect whether it extends far enough to pass through the whole region that needs separating.

If the preview creates one body instead of two, the tool may only touch the body, may not fully divide it, or may produce a zero-thickness or otherwise invalid result. Move the tool slightly and rebuild. Also inspect the model from more than one direction: a view can make a tool appear to cross the solid when it actually runs along an edge or face.

If there are too many bodies, the trim tool may intersect multiple regions or multiple existing bodies. Review the resulting-body list and the model’s solid bodies before accepting the feature. You may need to use a different trim tool, adjust its extent or position, or handle separate bodies in distinct operations.

If the feature becomes invalid after an edit, check whether later features depend on faces or edges that the split changed. Downstream references can fail when a cut changes the topology of a part. Re-select the appropriate references in affected features, and consider using more stable references such as planes, axes, or sketches where that suits the design.

Practical example: splitting a block for two components

Suppose a 100 mm-long block needs to become two equal pieces. Create a plane 50 mm from one end face, then use that plane as the trim tool in Split. After clicking Cut Part, verify that the preview shows two solid bodies of the expected size. Accept the feature and save the multibody part.

To create separate files, save each body with a descriptive file name. Check the saved documents and, if needed, insert them into an assembly. If the split must include a 1 mm gap in the assembled design, do not assume that splitting at the center automatically creates it. Position the cutting geometry and model the intended clearance explicitly, or adjust the component geometry to match the design requirements.

This example also shows why the split plane should be defined from a meaningful reference. If the block’s overall length later changes, a plane dimensioned by a fixed 50 mm offset may no longer divide it equally. A mid-plane reference or an equation-driven design may better represent the intended relationship, depending on how the model is built.

Frequently Asked Questions

Can SOLIDWORKS split one part into two separate files?
Yes. First use Split to create separate solid bodies, then use Save Bodies to save the selected bodies as individual part documents. The Split feature alone creates bodies in the part; it does not necessarily create separate files.

Can I split a part with a plane?
Yes. A plane is a common trim tool for a straight division. Position it so it crosses the solid and creates separate volumes, then select it in the Split PropertyManager and calculate the cut.

Why does Split create only one body?
The trim tool may not pass through the solid in a way that separates it, or it may only touch the model. Check the tool’s position and intersection, then rebuild and inspect the preview. A cut that leaves the solid connected will not produce two independent bodies.

What is the difference between Split and Split Line?
Split divides a solid body into bodies. Split Line divides or marks faces by creating edges, but it generally does not separate the solid into independent bodies. Choose the feature based on whether you need separate volumes or only divided face regions.

Can I edit the two bodies separately after splitting?
Yes. You can select bodies for later features within the multibody part, or save them as separate part files for independent document-level work. If you save bodies with references to the source, preserve those references if you want source changes to propagate.

Related

Try it: the Date Difference Calculator: days, months, years and weekdays between two dates, with the DATEDIF formulas.

More in How-to basics

Sources: Function behaviour and menu paths: Microsoft Support documentation for Excel. Method & sources

Spotted an error in this guide? Let us know.