SOLIDWORKS Split Function: How to Split Part Bodies

Formulas & functions · Updated November 22, 2026

Use the Split feature to divide a solid body in a SOLIDWORKS part with a plane, surface, face, or suitable sketch. Open the part, choose Insert > Features > Split, select a trim tool that crosses the body, click Cut Part, and decide which resulting bodies to keep or save. Split is useful for separating geometry into manageable bodies or creating separate part files; it does not simply draw an edge on a face.

The steps below describe the standard part-modeling workflow in SOLIDWORKS. The exact appearance of the PropertyManager can vary slightly by release, but the main sequence—select a trim tool, cut the part, then manage the resulting bodies—is the same.

What You’ll Need

  • A SOLIDWORKS part document. Split is a part feature. If your model is an assembly, edit the part that contains the geometry you want to divide.
  • A solid body to split. The trim tool must pass through or otherwise divide the solid in a way that creates valid resulting bodies. You can also use Split in a multibody part.
  • A trim tool. Common choices include a reference plane, surface, planar face, or sketch. Create one first if the model does not already have suitable geometry.
  • A plan for the result. Decide whether you want to retain multiple bodies in one part file or save selected bodies as separate part files. If you intend to make separate files, choose a folder and naming approach.

Step-by-Step

  1. Open the part and inspect the body. Open the part document and rotate or section the model as needed to understand where the split should occur. In the FeatureManager design tree, check whether the part contains one solid body or several. A split acts on the selected geometry, so identifying the target body and intended cut location first helps avoid dividing the wrong area.
  2. Create or choose a trim tool. Decide what geometry will define the split. A reference plane is often easiest for a straight, predictable division. To add one, use Insert > Reference Geometry > Plane, define its position using a face, plane, or other references, and confirm it. For a more complex boundary, create a surface or sketch that intersects the body where the separation is needed. The tool must actually divide the solid; a plane that only touches its outside face may not produce two bodies.
  3. Start the Split feature. Choose Insert > Features > Split. You can also search for Split using the SOLIDWORKS command search if you cannot find the menu item. The Split PropertyManager opens. Keep the part document active: the command is intended for part geometry, not for directly cutting an assembly into new part files.
  4. Select the trim tool. In the PropertyManager, click in the Trim Tools selection box, then select the plane, surface, face, or sketch in the graphics area or FeatureManager tree. If the selection is difficult, expand the tree and select the named feature there. Check the preview and confirm that the selected tool passes through the intended region. If the wrong item is listed, select it in the box and remove it before choosing another.
  5. Cut the part. Click Cut Part in the PropertyManager. SOLIDWORKS calculates the split and displays the resulting bodies. This is the point to verify whether the tool made the intended division. A single resulting body usually means the tool did not divide the solid, or the cut did not create a separate valid region. If the preview is wrong, cancel or adjust the trim tool rather than accepting an unintended result.
  6. Choose the bodies to keep. Review the Resulting Bodies list and its selections. Select the bodies you want to retain in the part; clear selections for bodies you do not want to keep, if the PropertyManager offers them as removable results. Rotate the preview and compare each body with the original model before confirming. Do not rely on the list order alone to identify a body—use the preview or highlight each listed body when available.
  7. Save bodies separately if needed. If you need individual part documents, use Save Bodies from the Split workflow. Specify a file name and destination for each body in the save interface, and review the proposed names before confirming. SOLIDWORKS can also offer creation of an assembly from the saved bodies; use that option only when an assembly containing those parts is part of your intended result. If you only need separate bodies within the original part, you do not have to save them as separate files.
  8. Confirm and check the feature. Accept the PropertyManager to finish the feature. Inspect the model in the graphics area and expand the Solid Bodies folder in the FeatureManager tree to confirm the expected bodies are present. If you saved separate files, open or verify them and check that each contains the intended geometry. Save the original part so the feature and its references are preserved.

A practical example is dividing a long bracket into two pieces at a planned joint. Create a reference plane at the joint location, run Split, select the plane as the trim tool, and click Cut Part. Check that the preview shows the two intended sections, retain both bodies, and use Save Bodies only if each section needs its own part document. If the bracket is hollow or has complicated internal geometry, inspect the preview from more than one angle to make sure the plane has separated all the material as intended.

Common Mistakes

  • Choosing a tool that does not intersect the solid. A reference plane can appear correctly positioned but miss the body or only touch it. Adjust its offset or orientation, or choose a tool that crosses the intended region.
  • Confusing Split with Split Line. Split creates separate solid bodies from a part. Split Line projects or uses geometry to divide faces or add edges, but it does not by itself separate a solid into bodies. Use Split Line when you need face boundaries for appearance, selection, or later operations rather than separate pieces.
  • Keeping or saving the wrong body. Similar-looking bodies and long body names can make the list hard to interpret. Identify each body in the preview before deselecting, naming, or saving it.
  • Expecting a saved body to update like a feature in the original file without checking its link. The original part and saved body documents may have references to one another depending on how they were created and maintained. Keep the source part and its referenced files together, and verify the saved parts after moving or renaming files.
  • Using a sketch that does not define a valid division. A sketch may be too short, positioned away from the solid, or unsuitable for cutting the whole cross-section. Check that its geometry intersects the target and forms a valid split for the body.

Tips

  • Use a reference plane for simple cuts. Planes are easy to reposition and make a clean, editable split. Give important planes meaningful names, such as Joint Plane or Trim at 40 mm, so they are easier to identify later.
  • Use the preview before confirming. Rotate the model, zoom in near the cut, and check every region where the trim tool meets the body. This is especially useful for parts with ribs, holes, pockets, or multiple intersecting features.
  • Plan names and file locations before saving bodies. Descriptive file names help distinguish components later. Use a consistent folder and avoid casually moving linked source and saved part files after creation.
  • Keep a working copy for major changes. Split is an editable feature, but changing the trim tool later can change the resulting bodies and downstream references. A copy gives you a safe comparison if the split is part of a significant redesign.
  • Use a different tool when the goal is different. For a cut that removes material, use an appropriate cut feature such as Cut-Extrude. For separate pieces created by dividing a body with a tool, use Split. For boundaries on a face without separating the solid, use Split Line.

Troubleshooting

Split is unavailable or the command fails to start: Confirm that a part document is active and that you are not trying to apply the feature directly to an assembly. Use command search to locate Split, or check the Insert menu. If the model is imported or has invalid geometry, try running the relevant geometry check or repair workflow before adding a feature.

No bodies appear after clicking Cut Part: Check that the trim tool is selected in the correct box and intersects the target body. A tool that merely touches the body, stops short, or lies entirely outside it may not divide it. Edit the plane position, extend or reposition the surface, or revise the sketch so the tool crosses the intended material, then click Cut Part again.

The result is one body instead of two: Examine the preview closely. The tool may divide only a face or a local region without separating the entire solid, or the apparent two sides may still connect through a rib or another bridge of material. Move the tool to a complete separation location, or use another feature first if you need to remove the connecting material.

The wrong geometry is split or disappears: Cancel or edit the feature, select the intended trim tool and body, and review the resulting-body selections. Use the graphics preview to identify the pieces rather than assuming the first list item is the desired one. If the feature has downstream references, inspect them after changing the split and repair any warnings caused by changed or missing bodies.

Saved files are missing or show unexpected geometry: Check the destination folder, file names, and whether the save operation completed. Reopen the source part and use Save Bodies again if necessary. If a saved file cannot find referenced geometry after files were moved, restore the original folder arrangement or use SOLIDWORKS file reference tools to locate the missing documents.

Frequently Asked Questions

Does Split create separate part files automatically?
Not by itself. Split creates resulting bodies in the part. Use the Save Bodies option when you want those bodies written as separate part documents.

Can I split a part with a plane?
Yes. A reference plane is a common trim tool. Position it so it crosses the body where the split should occur, then select it in the Split PropertyManager and click Cut Part.

Can I keep both sides of a split?
Yes. Review the resulting-body selections and retain both bodies if both are needed. They can remain in the same multibody part, or you can save them separately.

What is the difference between Split and Split Line?
Split divides a solid into separate bodies. Split Line creates boundaries on faces using selected geometry; it does not, on its own, break the solid into separate bodies.

Can I split a body more than once?
Yes. You can add further Split features to divide resulting geometry, provided each trim tool creates valid bodies. Recheck body selections and downstream features after each additional split.

Why does my sketch not work as a trim tool?
It may not intersect the solid, may not define a complete separation, or may not be suitable for the selected geometry. Check its plane, position, and extent, then inspect the preview. A reference plane or surface may be simpler for the intended cut.

Related

Try it: the Formula Explainer: paste any formula and see each function and reference in plain English.

More in Formulas & functions

Sources: Function behaviour and menu paths: Microsoft Support documentation for Excel. Method & sources

Spotted an error in this guide? Let us know.