CATIA Drafting: How to Split a Line

How-to basics · Updated November 22, 2026

In CATIA Drafting, use the Split command in the 2D geometry tools: start the command, select the line to divide, then select a cutting element that crosses it at the desired location. The line becomes separate segments at the intersection; if you want to remove a piece rather than keep both sides, use a trim or break operation instead.

What splitting a line does in a drawing

Splitting changes one 2D geometric element into multiple elements at a boundary. For a straight line crossed once by a cutter, the result is usually two line segments that meet at the intersection. Both remain visible, but each can be selected and edited independently. Splitting is useful when you need to change only one part of a drawn edge, apply different graphic properties to separate portions, or create a precise endpoint for another drafting operation.

A split is not the same as visually placing a mark on a line. A displayed intersection, a point symbol, or a dimension witness line does not necessarily divide the underlying line object. After splitting, you should be able to select one side without selecting the other. This independent selection is the practical test that the operation worked.

The instructions here describe the usual CATIA V5 Drafting workflow. CATIA releases, installed configurations, and customized toolbars can differ, so the Split icon may not appear in the same place in every interface. Make sure you are editing 2D drawing geometry, rather than trying to edit an edge that belongs to a generated 3D view.

Step-by-step: split a line with a crossing element

  1. Open the drawing sheet and identify the line you want to divide. If it belongs to a view generated from a 3D model, first check whether that view permits 2D geometry editing.
  2. Make or identify a cutting element that intersects the target line at the intended division point. A short temporary line is often convenient if no suitable edge or line is already there.
  3. Choose Split from the available 2D geometry modification tools. If the icon is not visible, look for it in the Drafting workbench’s geometry-modification toolbar or use the command search available in your CATIA release.
  4. Select the line to split, then select the crossing element as the cutter, following the command prompts shown on screen. Some interface versions or command contexts may prompt for the elements in a different order; follow the prompt rather than relying only on this description.
  5. Confirm the operation if CATIA asks for confirmation. Check that the target now has separate selectable portions and that the desired intersection became an endpoint.
  6. Remove a temporary cutter if it is no longer needed. Select only that construction element and delete it; do not delete either of the new line segments by mistake.

For example, suppose a horizontal line runs from x = 0 to x = 100 and you need a division at x = 40. Place a vertical cutter through x = 40, split the horizontal line, and verify that the results are the 0–40 and 40–100 portions. The coordinates are only an example: the important point is that the cutter crosses the line exactly where you want the new endpoint.

Choosing and placing the cutting element

The cutter determines where the split happens, so its intersection with the target matters more than its length or appearance. A straight temporary line is a straightforward choice for a straight target. Position it using drawing constraints, snapping, or a known geometric reference when precision matters; estimating the location by eye can produce an endpoint that looks right but is slightly misplaced.

Before splitting, consider whether the cutter intersects the target once or several times. A cutter that crosses a long line twice can create more divisions than intended, depending on the command’s behavior in your release. Keep the cutter short enough to cross the target only at the intended location, or use a more suitable existing boundary. If the command previews the affected sections, inspect the preview before accepting.

  • Existing geometry: Use a real crossing edge or line when its intersection is the desired division point.
  • Temporary geometry: Create a line through the required location, perform the split, and delete the temporary line afterward if it should not appear in the drawing.
  • Exact position: Use a dimension, alignment, or other reliable reference to locate the intersection rather than relying on visual placement alone.

A point or endpoint can be a useful location reference, but whether it can serve directly as the splitting boundary depends on the command and release. If CATIA will not accept a point as the cutter, create a small crossing line through that point and split with the line instead. This gives the command a clear intersecting element.

Split, trim, break, and break view are different

These terms are easy to confuse because each can change what a drawing looks like. A split normally preserves the geometry on both sides of the division and makes the portions separate elements. A trim removes an unwanted portion up to a boundary. A break operation may remove a section of 2D geometry, while a break view creates a shortened representation of a long component in a drawing view. The exact available commands and their names depend on the CATIA workbench and release.

  • Split: Divide an element so its resulting sections can be selected or edited separately.
  • Trim: Cut away geometry that extends beyond, or between, selected boundaries.
  • Break in 2D geometry: Remove a portion of an element, where that command is available.
  • Break view: Shorten the displayed length of a drawing view without changing the actual 3D part length.

If your goal is to make a gap, splitting alone may not produce the result you expect because it can leave both segments touching at the intersection. Split at the two ends of the intended gap, then remove the middle portion with an appropriate trim or deletion operation. If your goal is simply to show a long shaft or similar part more compactly, investigate the drawing’s break-view tools rather than splitting a line in the view.

Working with generated views and 2D geometry

A line visible on a drawing sheet may be either editable 2D geometry or an edge generated from a 3D model. That distinction affects what commands can do. A generated view is linked to model geometry and drawing-generation settings; directly modifying its projected edges may be restricted, or an update may restore geometry from the model. A separately drawn line on the sheet is ordinary 2D geometry and is generally the intended target for a drafting split.

If CATIA refuses to select or split an edge, check whether the view is active and whether the item is generated geometry. Depending on the drawing setup, you may need to activate the view, use a permitted 2D component or annotation layer, or create an independent 2D line rather than alter the projected edge. Do not assume that deleting or editing a generated edge changes the 3D model: drafting geometry and the model have different roles.

Also consider associativity. Dimensions, constraints, and annotations may refer to an element or one of its endpoints. Dividing that element can affect which portion an annotation references, or make an association less useful. After editing a line that is dimensioned or used as a reference, inspect the relevant dimensions and annotations and update or reattach them if necessary.

Common problems and practical fixes

  • The Split command is missing: Confirm that you are in the Drafting workbench and looking at 2D geometry modification tools. Toolbars may be hidden or rearranged, and the exact layout varies by installation. Use the interface’s command search if available.
  • The target line will not select: It may be part of a generated view, the view may not be active, or another object may be obscuring the selection. Activate the correct view and check the element type before trying again.
  • The split happens at the wrong place: The cutter may cross the target somewhere other than the intended point, or may intersect it more than once. Adjust the cutter and repeat the operation.
  • The whole line still highlights: The operation may not have completed, or the two resulting segments may be coincident or selected together. Exit the command and click each side separately to test the result.
  • Nothing changes after selecting elements: Read the command prompts, verify that the cutter actually intersects the target, and check whether the selected objects are eligible 2D elements.
  • A dimension or annotation looks wrong afterward: The split may have changed the element or endpoint it references. Inspect the association and reattach it to the intended segment if needed.

Undo is useful if the result is not what you intended. Undo the operation promptly, correct the cutter or selection, and retry. If the drawing is complex, save a copy before making a batch of geometry edits. A clean, unambiguous cutter and a quick independent-selection check prevent many avoidable mistakes.

How to verify and tidy the result

After the split, zoom in on the intersection and select each side in turn. The portions should behave as separate elements, and the new endpoint should sit at the crossing. If selection is difficult because the lines overlap other geometry, temporarily hide or move unrelated elements only when appropriate, or use the selection tools available in your CATIA setup.

Review the drawing at its normal working scale as well as close up. A tiny gap can be hard to see at normal scale, while an inaccurate endpoint may become obvious when enlarged. Check that line appearance, layer or view placement, and any connected annotations still make sense. If you used a temporary cutter, remove it only after confirming the split; leaving an unintended line in the sheet can be mistaken for design geometry later.

Finally, save the drawing and, where relevant, update it in accordance with the model and drawing workflow in use. If an update changes or restores a generated edge, that is a clue that the edge is controlled by the 3D view rather than being independent 2D geometry.

Frequently Asked Questions

Can I split a CATIA Drafting line at an exact point?
Yes, provided the Split command can use geometry intersecting at that point. Place a cutter through the exact location using a reliable reference or constraint, then split and verify the resulting endpoint. If a point alone is not accepted as the cutter, use a crossing line through it.

Does splitting a line create a gap?
Usually, no. Splitting divides the element but keeps the resulting portions meeting at the division point. To create a gap, split at both ends of the desired gap and remove the middle portion with a suitable trim or deletion operation.

Why can’t I split an edge in a generated view?
The edge may be controlled by the projected 3D model rather than being independent drawing geometry. Check that the view is active and determine whether your setup permits editing that edge. If it does not, use separate 2D geometry for the drafting mark or modify the source model as appropriate.

How do I split a line without leaving the cutting line?
Use a temporary crossing element, complete the split, and then select and delete only the cutter. Confirm that the two intended line segments remain independently selectable before saving.

What should I use to remove part of a line?
Use a trim or other appropriate removal command when the objective is to discard geometry. Split is for creating separate portions, not necessarily for erasing one of them. For shortening a projected component in a view, use a break-view feature instead of changing the underlying line.

Related

Try it: the Date Difference Calculator: days, months, years and weekdays between two dates, with the DATEDIF formulas.

More in How-to basics

Sources: Function behaviour and menu paths: Microsoft Support documentation for Excel. Method & sources

Spotted an error in this guide? Let us know.